E3D Titan Extruder with BLTouch sensor

[sveske]

for me te ultimate setup :-)

Printed and assembled Rocks carrier version. I have not placed it on printer yet, since i am still building it, but running out of time for now :-) (vacation starts Friday, and so much that needs to be done before lol)
It is a little tricky to assemble BUT possible. I like that it stays within the original frame :-)

As I have pointed out, way to many times ;-)
I would love a Bltouch sensor on the carrier.

www.thingiverse.com/thing:1229934

My initial idea, was to design a cooler for prints, with a holder for BLtouch (on paper, and ask for help again lol)
something like the one here:
www.thingiverse.com/thing:1615400/#comments
arcaded.discussion.community/post/lpa-fanduct-version-4-8139028?&trail=15

but I cant seem to figure out how it should be adapted to our printer...
Also I am trying to figure out, if there is any extra space, to make a mount on the outside of the carrier? on any side?
like this one www.thingiverse.com/thing:1315514
since mine is not build, I can not check!
My printer has a print height of 36cm so if I loose 10mm or something like that, That would not be considered a problem, but regarding xy I would prefer to keep the 20x20cm

So any tips/ideas would be great

[sveske]

Update :-)
finally assembled my printer (got home from vacation.)
all I need to do, is wire it up! BUT I want it working with the BLtouch in first go ;-)

I have been trying to figure out how to get it working/where to place it.
therefor I have assembled the printer, so I could look at it.
I can see, why no one, have been able to find a spot for the BLTouch!

Printed and assembled www.thingiverse.com/thing:1598224
I know the right mount High.... When you look at the gantry, at the spot where the fan, cooling the e3dV6 sits, the top of that opening, is perfekt mount high!
BUT where to mount it? I have used alot of time, trying to figure it out :-( i am so bad at this! BUT can it be, that the only posible space, is facing the front, between the 2 holders for the belt? (remember on this design www.thingiverse.com/thing:1598224 not the original one)

cheers
Jesper

[carlos]

That seems to be the only available spot. on that carriage.

Also did you figure out the wiring for the BLtouch?

[sveske]

I am using the Ramps, so I thing I have the wires ok ;-) at least I have a guide ;-)

BUT I would really appreciate if you could upload your design file, so I an edit it. the STL file has lost some data, so for a newb as me, it is hard to change it.
My idea is to open up, and place it between thouse 2 holders inside the gantry. need to try it ;-) but needs to move the holes, nuts and other a little.
also need to melt some dropin m3 nuts into it, since there is no room for normal nuts, due to the axel.

sorry my bad English!

Jesper

[carlos]

That's rock75 design, hopefully he can pass along the original to work with.

[sveske]

You are right :-) my bad.
I hope he can, then I THINK I can make it work... perhaps ;-)

The printer is ready for wires and belt. BUT I will not do it untill I can get the right Gantry printet ;-) or atleast a prototype lol
Jesper

[jjlink]

Aug 9, 2016 6:37:02 GMT sveske said:

You are right :-) my bad.
I hope he can, then I THINK I can make it work... perhaps ;-)

The printer is ready for wires and belt. BUT I will not do it untill I can get the right Gantry printet ;-) or atleast a prototype lol
Jesper

Rock's gantry is here: www.thingiverse.com/thing:1598224
You also may need this: www.thingiverse.com/thing:1664902

[sveske]

Aug 9, 2016 12:37:06 GMT jjlink said:

Aug 9, 2016 6:37:02 GMT sveske said:

You are right :-) my bad.
I hope he can, then I THINK I can make it work... perhaps ;-)

The printer is ready for wires and belt. BUT I will not do it untill I can get the right Gantry printet ;-) or atleast a prototype lol
Jesper

Rock's gantry is here: www.thingiverse.com/thing:1598224
You also may need this: www.thingiverse.com/thing:1664902

Yeap as STL, I need to change it :-)
and the STL file, I can not change.
I am using the Fusion 360.

Jesper

[rock75]

Aug 9, 2016 12:56:51 GMT sveske said:

Aug 9, 2016 12:37:06 GMT jjlink said:

Rock's gantry is here: www.thingiverse.com/thing:1598224
You also may need this: www.thingiverse.com/thing:1664902

Yeap as STL, I need to change it :-)
and the STL file, I can not change.
I am using the Fusion 360.

Jesper

Hey Jesper, sorry for the late reply here. Been super busy lately and was out of the country for a few days on top of being busy.

I updated the files on thingiverse and added the Fusion360 file for you! www.thingiverse.com/thing:1598224
Let us know how it turns out.

Cheers -
Rock

[sveske]

Aug 10, 2016 6:04:04 GMT rock75 said:

Aug 9, 2016 12:56:51 GMT sveske said:

Yeap as STL, I need to change it :-)
and the STL file, I can not change.
I am using the Fusion 360.

Jesper

Hey Jesper, sorry for the late reply here. Been super busy lately and was out of the country for a few days on top of being busy.

I updated the files on thingiverse and added the Fusion360 file for you! www.thingiverse.com/thing:1598224
Let us know how it turns out.

Cheers -
Rock

Your the best, thank you. I will try and modify it tonight, or tomorrow :-)
Just to be a problem ;-) could you also upload your fan "thing" since I am trying to make one, that puts air from 3 sides. :-) and would reuse your top part, since it fits so nicely ;-)


Thanks for the help :-)

/Jesper

[sveske]

Did the first design change yesterday, one of my problems is I need to move the 2 holders/locks for the belt, a little towards the corner, is that a problem? 5mm i think it was!


jesper

[carlos]

That should work, no reason you can't move them over.

[sveske]

work in progress, never done this before, so be gentle, or even better make a better version ;-)

www.thingiverse.com/thing:1720643

that is my shot at it! THX to Rock for his versin version :-)

[sveske]

dont print, it WILL work, but I am redesigning, for better view at the LED light when probing.

[sveske]

New version, just assembled it, looks ok.
www.thingiverse.com/thing:1720643