|
|
Post by jjlink on May 12, 2016 23:07:10 GMT
Nice, I just ordered the Titan. Update: Wow MatterHackers are fast, It arrived today! |
|
|
|
Post by jjlink on May 13, 2016 21:13:32 GMT
Nice, I just ordered the Titan. Update: Wow MatterHackers are fast, It arrived today! Another surprise the Short stepper motor from stepperonline via ebay ( goo.gl/XeVZUk ) arrived today (all the way from China). That was supper fast shipping! I sure looks to me that Thomas Sanladerer is right the Titan extruder with this small light motor looks like a wining combination. |
|
sveske
New Member
Decided next 3d printer build :-)
Posts: 45 
|
Post by sveske on May 14, 2016 13:42:55 GMT
so envy, just got mail, my pancake nema17 is 30 days away :-(
was the files comming? ;-)
|
|
carlos
Junior Member
Posts: 94
|
Post by carlos on May 14, 2016 20:36:35 GMT
Hey guys here's the files for you all to play with www.thingiverse.com/thing:1563651It still needs a lot of work, not happy about how the e3d fan attaches. Ends up letting a lot of air below it, for now I just covered the bottom of the carriage with some Kapton tape, if you don't you'll see a 5 degree difference. But this should get you started. |
|
|
|
Post by rock75 on May 23, 2016 4:28:05 GMT
Hey guys here's the files for you all to play with www.thingiverse.com/thing:1563651It still needs a lot of work, not happy about how the e3d fan attaches. Ends up letting a lot of air below it, for now I just covered the bottom of the carriage with some Kapton tape, if you don't you'll see a 5 degree difference. But this should get you started. Thanks Carlos! Curious, which cable chain did you use? I printed up some that look very similar but do not quite fit. Also, I would like to make a couple changes to your design but not sure how to modify an .stl, could you share your source file for us to work with. Thanks! Rob |
|
|
|
Post by waffleb0t on May 23, 2016 18:17:29 GMT
|
|
carlos
Junior Member
Posts: 94
|
Post by carlos on May 23, 2016 20:45:24 GMT
Yes I modified it to be wider then what's been floating around online. To be honest, I would change it again one more time, cause it's a bit of a pain to push through. Anyway, I updated the thingiverse link with the additional files. And sketchup file for you to modify and play with.
|
|
|
|
Post by rock75 on May 24, 2016 0:10:46 GMT
Yes I modified it to be wider then what's been floating around online. To be honest, I would change it again one more time, cause it's a bit of a pain to push through. Anyway, I updated the thingiverse link with the additional files. And sketchup file for you to modify and play with. Thanks Carlos! If what I'm thinking works I will definitely share what I come up with. Cheers Rock |
|
carlos
Junior Member
Posts: 94
|
Post by carlos on May 24, 2016 2:40:55 GMT
Great, looking forward to printing up what you modify  |
|
|
|
Post by rock75 on May 31, 2016 2:42:58 GMT
Great, looking forward to printing up what you modify Hey Carlos, I liked your design for the Titan, but I really wanted to keep everything facing the front. Here is what I came up with, basically just rearranged everything on Andrew's original gantry. Hey guys, here is a new E3D Titan Extruder compatible gantry for the Eclips3D printer. Please note, I have not installed and tested this yet. Right after I got it printed my wife confiscated my 3D printer room and we turned it into her new sewing room. The Eclips3D has now been relocated to the garage and I have not had time to set everything up again.  If you print one up, let me know if you have any troubles. I will update as soon as I can install mine and test it out. www.thingiverse.com/thing:1598224 |
|
|
|
Post by sveskes on May 31, 2016 7:44:20 GMT
Great, looking forward to printing up what you modify Hey Carlos, I liked your design for the Titan, but I really wanted to keep everything facing the front. Here is what I came up with, basically just rearranged everything on Andrew's original gantry. Hey guys, here is a new E3D Titan Extruder compatible gantry for the Eclips3D printer. Please note, I have not installed and tested this yet. Right after I got it printed my wife confiscated my 3D printer room and we turned it into her new sewing room. The Eclips3D has now been relocated to the garage and I have not had time to set everything up again. If you print one up, let me know if you have any troubles. I will update as soon as I can install mine and test it out. www.thingiverse.com/thing:1598224GREAT, thanks, will look into it :-) |
|
sveske
New Member
Decided next 3d printer build :-)
Posts: 45
|
Post by sveske on May 31, 2016 11:07:13 GMT
Great, looking forward to printing up what you modify Hey Carlos, I liked your design for the Titan, but I really wanted to keep everything facing the front. Here is what I came up with, basically just rearranged everything on Andrew's original gantry. Hey guys, here is a new E3D Titan Extruder compatible gantry for the Eclips3D printer. Please note, I have not installed and tested this yet. Right after I got it printed my wife confiscated my 3D printer room and we turned it into her new sewing room. The Eclips3D has now been relocated to the garage and I have not had time to set everything up again. If you print one up, let me know if you have any troubles. I will update as soon as I can install mine and test it out. www.thingiverse.com/thing:1598224Question is :-) if any of you great designers, also can make room for a probe? ' I was considering this one, unless someone know of a better solution? I want to be able to switch between different types of glas and even plastik print surface. :-) |
|
carlos
Junior Member
Posts: 94
|
Post by carlos on May 31, 2016 20:04:37 GMT
rock75 I originally had it that way, but opted to to turn it cause it gave me more room on the X-axis. Have a much larger print area then the stock printer. You did an excellent design. Saved it for future builds, rock on!
|
|
sveske
New Member
Decided next 3d printer build :-)
Posts: 45
|
Post by sveske on Jun 4, 2016 21:35:32 GMT
Ok, now I ordered the :
I have ordered the original hotend, and the Titan extruder. In my world, that should make an interesting pack.
Now waiting for the parts, and as I said, I stink at 3d designing, SO if someone could fit the sensor into the suggestion here, that would be my first try :-)
THANKS :-)
Greetings from Denmark
|
|
|
|
Post by jjlink on Jun 4, 2016 22:15:26 GMT
Great, looking forward to printing up what you modify Hey Carlos, I liked your design for the Titan, but I really wanted to keep everything facing the front. Here is what I came up with, basically just rearranged everything on Andrew's original gantry. Hey guys, here is a new E3D Titan Extruder compatible gantry for the Eclips3D printer. Please note, I have not installed and tested this yet. Right after I got it printed my wife confiscated my 3D printer room and we turned it into her new sewing room. The Eclips3D has now been relocated to the garage and I have not had time to set everything up again. If you print one up, let me know if you have any troubles. I will update as soon as I can install mine and test it out. www.thingiverse.com/thing:1598224I printed up both of them and tried assembling the Titan on each of them. Carlos's design will definitely work I just haven't been in a hurry to take apart the existing original gantry since the printer is working so well. The second looks good until you try to mount the E3d v6 heat-sink into the Titan. There is a screw on the Titan under the heat-sink that needs to go on first. Once that screw is in the seems to be no way to get the heat-sink into the Titan since there is not enough room to get it positioned through the gantry. |
|
